version 1.3, 2004/06/08 23:16:03
|
version 1.9, 2006/09/15 20:54:55
|
Line 37 http://www.lon-capa.org/
|
Line 37 http://www.lon-capa.org/
|
<perlscript mode="fg"> |
<perlscript mode="fg"> |
print "Checking to be sure the Network Time Protocol is running properly.\n"; |
print "Checking to be sure the Network Time Protocol is running properly.\n"; |
print "For more information on ntpd please see http://www.ntp.org/\n"; |
print "For more information on ntpd please see http://www.ntp.org/\n"; |
if (! -e "/etc/init.d/ntpd") { |
my $NTPD; |
|
if (-e "/etc/init.d/ntpd") { |
|
$NTPD = "ntpd"; |
|
} elsif (-e "/etc/init.d/xntpd") { |
|
$NTPD = "xntpd"; |
|
} elsif (-e "/etc/init.d/ntp") { |
|
$NTPD = "ntp"; |
|
} else { |
print "ntp is not installed.\n"; |
print "ntp is not installed.\n"; |
exit; |
exit; |
} |
} |
my $value = `/etc/init.d/ntpd status`; |
my $value = `/etc/init.d/$NTPD status`; |
if ($value !~ / running/) { |
if ($value !~ /running/) { |
print "WARNING: ntp is installed but is not currently running.\n"; |
print "WARNING: ntp is installed but is not currently running.\nPlease verify the configuration of ntp in /etc/ntp.conf and /etc/ntp/step-tickers\nStart ntp by executing\n /etc/init.d/$NTPD start\n"; |
} |
} |
# chkconfig barfs to stderr if the target isn't set up right. |
# chkconfig barfs to stderr if the target isn't set up right. |
my $restartchk = `/sbin/chkconfig --list ntpd 2>/dev/null`; |
my $restartchk = `/sbin/chkconfig --list $NTPD 2>/dev/null`; |
if ($restartchk eq '') { |
if ($restartchk eq '') { |
print "WARNING: ntpd is either not installed or not configured to run at boot.\n"; |
print "**** WARNING: ntpd is either not installed or not configured to run at boot.\n"; |
exit; |
exit; |
} |
} |
if ($restartchk =~ /^error reading information on service / || |
if ($restartchk =~ /^error reading information on service / || |
$restartchk !~ /\d:(on|off)/) { |
$restartchk !~ /\d:(on|off)/) { |
print "WARNING: Unable to check status of ntpd with /sbin/chkconfig.\n"; |
print "**** WARNING: Unable to check status $NTPD with /sbin/chkconfig.\n"; |
exit; |
exit; |
} |
} |
if ($restartchk !~ /\s3:on/) { |
if ($restartchk !~ /\s3:on/) { |
print "WARNING: ntpd is not set to start at runlevel 3. To correct this run:\n/sbin/chkconfig --level 3 ntpd on\n"; |
print "**** WARNING: ntpd is not set to start at runlevel 3. To correct this run:\n/sbin/chkconfig --level 345 $NTPD on\n"; |
exit; |
exit; |
} |
} |
if ($restartchk !~ /\s5:on/) { |
if ($restartchk !~ /\s5:on/) { |
print "WARNING: ntpd is not set to start at runlevel 5. To correct this run:\n/sbin/chkconfig --level 5 ntpd on\n"; |
print "**** WARNING: ntpd is not set to start at runlevel 5. To correct this run:\n/sbin/chkconfig --level 345 $NTPD on\n"; |
exit; |
exit; |
} |
} |
</perlscript> |
</perlscript> |